HP MSA 2040
User Guide
Advertising
Feb 22, 2017 ADD new Server to a SAN network, zone in SAN switch and map in the msa2040, then connect to disks in win server 2012. HP MSA 2040 SAN Dual Controller SFF Storage/S-Buy. HP MSA System Racking Or point us to the URL where the manual is located. This document contains cable configuration information for HP MSA 2040 controller User Always operate the array in accordance with the user manual. HP MSA 2040 HP MSA 2040 SAN Controller GL100R002. HPE MSA 2040, a High-Performance Storage array designed for Entry-Level Hewlett Packard Enterprise users desiring 8Gb/16Gb Fibre Channel (FC), 1 GbE/10 GbE iSCSI, or 12Gb SAS connectivity with 4 host ports per controller. MSA 2040 Storage models The MSA 2040 enclosures support either large form factor (LFF 12-disk) or small form factor (SFF 24-disk) 2U chassis, using either AC or DC power supplies. MSA Storage models include MSA 2040 SAN and MSA 2040 SAS controllers, which are introduced below. NOTE: For additional information about MSA 2040 controller modules.
HP Part Number: 723983-002
Published: September 2013
Edition: 2
Abstract
This document describes initial hardware setup for HP MSA 2040 controller enclosures, and is intended for use by storage system
administrators familiar with servers and computer networks, network administration, storage system installation and configuration,
storage area network management, and relevant protocols.
Advertising
Table of contents
Popular Brands
Popular manuals
Advertising
44
Bobcat s175 service manual download. Connecting to the controller CLI port
1.
Locate the DVD included with your MSA 2040 storage device.
2.
Insert the DVD into the drive on a Linux or Windows computer on the network that is connected to your
controller enclosure.
Use Autorun or manually start the DVD.
The MSA Device Discovery Tool will run.
4.
Follow the instructions to discover the IP addresses of the controller or controllers.
Record these IP addresses so that you can specify them whenever you manage the controllers using the
SMU or the command-line interface.
Alternatively, you can set network port IP addresses using the command-line interface on HP-UX, Windows,
and Linux platforms.
Setting network port IP addresses using DHCP
1. Op-com diagnostic interface user manual software.
Look in the DHCP server’s pool of leased addresses for two IP addresses assigned to “HP MSA
Storage.”
2.
Use a ping broadcast to try to identify the device through the ARP table of the host.
If you do not have a DHCP server, you will need to ask your system administrator to allocate two IP
addresses, and set them using the command-line interface during initial configuration (described
below).
Setting network port IP addresses using the CLI port and cable
If you did not use the MSA Device Discovery Tool to set network port IP values, set them manually using the
command-line interface port and cable. If you have not done so already, you need to enable your system
for using the command-line interface port [also see
NOTE:
For Linux systems, see
. For
Windows systems see
.
Network ports on controller module A and controller module B are configured with the following
factory-default IP settings:
•
Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B)
•
IP Subnet Mask: 255.255.255.0
•
Gateway IP Address: 10.0.0.1
Hp Msa 2040 San Storage User Manual Download
If the default IP addresses are not compatible with your network, you must set an IP address for each
network port using the command-line interface embedded in each controller module. The command-line
interface enables you to access the system using the USB (universal serial bus) communication interface
and terminal emulation software. The USB cable and CLI port support USB version 2.0.
Use the CLI commands described in the steps below to set the IP address for the network port on each
controller module. Once new IP addresses are set, you can change them as needed using the SMU. Be
sure to change the IP address via the SMU before changing the network configuration.
NOTE:
Changing IP settings can cause management hosts to lose access to the storage system.
1.
Hp Msa 2040 Configuration Guide
User manual in chinese compulsory regulations in china printers. From your network administrator, obtain an IP address, subnet mask, and gateway address for
controller A, and another for controller B.
Record these IP addresses so that you can specify them whenever you manage the controllers using the
SMU or the CLI.
2.
Use the provided USB cable to connect controller A to a USB port on a host computer. The USB mini 5
male connector plugs into the CLI port as shown in
(generic controller module is shown).
Hp Msa 2040 Support
Advertising
Popular Brands
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |